Get free quotes

Free pump calculator

Pipe friction loss calculator

Choose the pipe, the length and the flow. It gives the friction loss in metres of head and in bar, the loss per 100 m and the speed of the water, and compares the sizes next to yours.

Pipe and flow

1 m³/h is 1,000 litres an hour, or about 16.7 litres a minute.

Bends, valves and joints. 10% is a fair start.

Result

Inside diameter
-
Speed of the water
-
Loss per 100 m
-
Friction loss
-
Pressure lost
-

The same flow in other HDPE PN16 sizes
PipeSpeedLoss

How the friction loss is worked out

The calculator uses the Hazen-Williams formula, the usual method for clean water at normal temperatures: head loss (m) = 10.67 × length × flow1.852 ÷ (C1.852 × inside diameter4.87), with the flow in m³/s and the diameter in metres. C is the roughness factor: 150 for new HDPE and PVC, 120 for galvanised steel, which gets rougher as it rusts and scales.

HDPE pipe is sold by its outside diameter, so the inside diameter depends on the pressure class. For PE100 pipe the wall is the outside diameter ÷ the SDR: SDR 17 for PN10 and SDR 11 for PN16. A 40 mm PN16 pipe is about 32.7 mm inside, a 40 mm PN10 about 35.3 mm.

Choosing the pipe size

  • Friction rises with roughly the square of the flow and falls steeply with the diameter: one size up often halves the loss or better.
  • Long surface runs to a tank or a field matter most. On a 300 m run, the pipe can cost more head than the borehole depth.
  • A borehole drop pipe must also carry the weight of the pump and the water column. Deep settings need a higher pressure class or steel column, whatever the friction says.
  • Muddy water, sewage and slurry need a bigger pipe and a higher speed to keep solids moving; this calculator is for clean water.

Put the result into the borehole pump size calculator to see what it does to the motor size.

Frequently asked questions

What pressure class of HDPE pipe do I need for a borehole?
The pipe at the pump sees the full head of the column above it, plus any pressure at the top. A pump pushing to 100 m of head puts about 10 bar on the bottom of the pipe, so PN10 is the bare minimum there and PN16 is the usual choice. Ask the supplier, and see pump cable and pipe.
What water speed should a pipe run at?
For pumped clean water, about 1 to 1.5 m/s is a common target. Faster pipes lose more head and knock harder when a valve shuts; slower pipes cost more to buy.
Does an old steel pipe lose more than a new one?
Yes. Rust and scale make the bore rougher and smaller. The C factor of 120 is for steel in fair condition; old, scaled steel can be much worse.

More calculators and guides

Free quote request, no obligation

Request pump cable and pipe quotes

Fill in the duty sheet the way a pump technician would: how deep the water is, how high it must go, how much you need, or what has to be pumped away. Pump suppliers, installers and repairers in your area quote you directly.

Pump duty sheetPump Cable and Pipe
Request
84788
Logged
2026-11-21

1The job

2How many (optional, it helps the quote)

Your ordernot to scale

-
-
-
-
-
-
Estimate
-

A rule of thumb, not a pump selection.

3Power and timing

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: pumps, boxes, cable, pipe or spares.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable suppliers, installers and repairers. See our privacy policy.

Get free pump quotes