Get free quotes

Free pump calculator

Borehole pump size calculator

Give the water level, the height to the tank, the pipe and the flow you want. It adds up the total head, checks the pipe and the borehole yield, and gives the duty point and a rough motor size to put on a quote request.

Borehole and lift

Where the water stands with the pump off.

From the yield test. Leave 0 if unknown.

Where the pump hangs.

Leave 0 if not tested.

1 m³/h is 1,000 litres an hour, or about 16.7 litres a minute.

0 when it fills an open tank.

Result

Pumping water level
-
Pipe friction
-
Total head
-
Duty point
-
Motor, roughly
-
Speed in the pipe
-
Water in 8 hours
-

How the total head is worked out

A pump is chosen by its duty point: a flow at a total head. The total head is every metre the pump has to push the water up, plus the losses on the way:

  • Pumping water level: the rest water level plus the drawdown, which is how far the water drops in the hole while the pump runs. The yield test gives both.
  • Height above ground to the top of the tank, or to the highest tap.
  • Pipe friction, worked out here with the Hazen-Williams formula over the whole pipe (the setting depth, the surface run and the rise), plus 10% for the bends, the non-return valve and the fittings.
  • Pressure at the outlet, if the water must arrive under pressure (for a pressure tank or straight to the house): 1 bar is about 10.2 m of head.

The hydraulic power is the flow (m³/h) × the total head (m) ÷ 367, in kW. Divided by the pump's efficiency, and rounded up to a standard motor size, that gives a rough motor size.

Worth knowing before you ask for quotes

  • Never size the pump on what you would like; size it on what the borehole gives. A pump that takes more than the yield runs the hole dry, and dry running burns out the motor and draws in sand.
  • Hang the pump well below the pumping water level, but not on the bottom of the hole, where it pulls in silt.
  • Pipe that is too small costs money every day in friction. Water at about 1 to 1.5 m/s in the pipe is a sensible target.
  • Over about 2.2 kW, borehole motors are usually three phase. Single phase sites need a pump that fits the supply.

Use the pipe friction calculator to compare pipe sizes, and the cable size calculator once you know the motor.

Frequently asked questions

What is total dynamic head?
Total dynamic head (TDH) is the total height the pump must lift the water, plus the friction losses in the pipe and any pressure needed at the outlet, all in metres of water. It is the head figure on a pump curve.
How do I find the water level in my borehole?
The yield test report from the driller gives the rest water level and the drawdown at the test flow. Without it, a borehole technician can measure the level with a dip meter. Water levels drop in a dry season, so design for the lower level.
Can I put a bigger pump in for more water?
Only if the borehole can give more. The yield, not the pump, sets the limit. See borehole pumps for how pumps are matched to the hole.

More calculators and guides

Free quote request, no obligation

Request borehole pumps quotes

Fill in the duty sheet the way a pump technician would: how deep the water is, how high it must go, how much you need, or what has to be pumped away. Pump suppliers, installers and repairers in your area quote you directly.

Pump duty sheetBorehole Pumps
Request
37590
Logged
2026-11-21

1The job

2The duty (optional, it helps the quote)

In section: the liftnot to scale

-
-
-
-
-
-
Estimate
-

A rule of thumb, not a pump selection.

3Power and timing

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: pumps, boxes, cable, pipe or spares.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable suppliers, installers and repairers. See our privacy policy.

Get free pump quotes